Deck Stair Calculator

in

Type it the way you read the tape: 68 1/2, 5' 8 1/2", 68.5 or 174cm.

Type your total rise and the answer appears here.

Code check runs as you type
Where to measure
Where to measure total riseTotal risemeasure straight downlevel off the finished deckdeck or floorfinished ground or floor

Measure from the top of the finished upper floor or deck straight down to where the bottom step will land. Not level ground? Measure at the landing spot.

Drag, or use the arrow keys
AdjustTread, riser, lumber, nosing, units — the drawing updates as you go

Steps

Top of stair

Lumber

Stringer stock

Space (optional)

Show results in

Cut sheet

Your marks, cuts and shopping list fill in here.

Code check

  • Runs as soon as you enter a total rise.

Based on the IRC (2021 R311.7 / 2024 R318.7). Local codes vary — confirm with your building department before building.

Building exterior deck stairs requires planning for outdoor grade variations, pressure-treated lumber, composite decking spans, and concrete landing pads. This deck stair calculator gives you exact stringer dimensions, tread board counts, framing square settings, and code checks for your deck project.

Enter your deck height above to see your exterior stair diagram and print a jobsite cut sheet.


How to Use This Deck Stair Calculator

  1. Measure finished deck height: Clamp a level to your deck extending over the rim joist. Measure down to where your concrete pad sits. Enter this in Total rise.
  2. Select decking material: Under Adjust, choose tread thickness (1” for 5/4 decking/composite, 1 1/2” for 2x lumber) and enter stair width.
  3. Verify stringer spacing and cuts: Review stringer count (12” OC for composite, 16” for wood), check that uncut throat is at least 5”, and print your cut sheet.

How Deck Stairs Are Calculated

Exterior deck stairs must satisfy residential building codes (IRC) and deck standards (AWC DCA 6).

1. Riser Count and Step Rise

Maximum riser height is 7 3/4 inches (7.75”). Calculate step count by dividing deck height by 7.75 and rounding up:

Risers = Deck Height ÷ 7.75, rounded up
Unit Riser Height = Deck Height ÷ Risers

2. Tread Depth and Deck Board Layout

Deck stairs use a 10 1/2” or 11” run so deck boards fit cleanly:

3. Total Horizontal Run

Because the upper deck surface serves as the final landing:

Treads = Risers - 1
Total Run = Treads × Tread Depth

Verify yard space for this run plus a 36-inch landing pad at the base.

4. Stringer Spacing and Structural Throat

5. Bottom Riser Cut and Concrete Landing Pad

Never rest stringers on bare soil. Rest them on a poured concrete pad or solid pavers:


Worked Example: 42” Deck Height

A backyard deck with a 42-inch finished height, 10 1/2-inch tread depth, and 5/4 decking (1” thick):

This configuration passes all IRC code checks with a comfortable 33.7° incline.


Residential Stair Code for Decks (IRC R311.7 / R318.7)

Outdoor stairs must comply with the same IRC standards as interior stairs:

Code Dimension IRC Requirement Deck Builder Practical Tip
Maximum Riser Height 7 3/4 inches All risers must match within 3/8” variance
Minimum Tread Depth 10 inches 10 1/2” fits two 5/4x6 boards cleanly
Tread Nosing 3/4” to 1 1/4” Created by overhanging deck boards
Maximum Variation 3/8 inch Check for settlement at bottom landing pad
Minimum Headroom 6 feet 8 inches Verify clearance under pergolas or eaves
Minimum Clear Width 36 inches Measure between inside faces of handrails
Handrail Requirement Required at 4+ risers Mount at 34” to 38” height above nosing
Landing at Base 36” in travel path Concrete pad, pavers, or sidewalk

Based on the IRC (2021 R311.7 / 2024 R318.7). Local codes vary — confirm with your building department before building.


Frequently Asked Questions

What spacing do I need between stringers on a deck?

For 2x6 wood treads, space stringers up to 16 inches on-center. For composite decking or 5/4 wood decking, reduce stringer spacing to 12 inches on-center to prevent spongy steps and sagging treads.

Do deck stairs need a concrete landing pad?

Yes. IRC code requires a landing at the bottom of exterior stairs measuring at least 36 inches in the travel direction. Resting stringers directly on dirt leads to rot and uneven settling.

How do I attach deck stringers to the rim joist?

Fasten stringers using approved metal stringer hangers (such as Simpson Strong-Tie LSCZ) or bolt a dropped treated 2x header under the rim joist to provide full bearing support for each stringer notch.

How many deck boards make up one stair tread?

Most builders use two 5/4x6 or two 2x6 boards per step. With actual widths of 5 1/2 inches each and a 1/4” drainage gap, two boards provide an 11 1/4” tread with a code-compliant 3/4” nosing overhang.

Why do I need to cut 1 inch off the bottom of my deck stringer?

The bottom cut compensates for tread thickness. Adding a 1-inch tread raises the first step. Trimming 1 inch off the bottom of the stringer ensures the first step matches the exact height of all subsequent steps.

What size lumber is required for deck stringers?

Always use 2x12 pressure-treated lumber rated for ground contact (AWPA UC4A). Using a 2x10 leaves under 3 1/2 inches of throat depth, violating the 5-inch structural requirement.