When a staircase is too tall for a single flight, or when room layout requires a 90-degree turn (L-shaped) or 180-degree turn (U-shaped switchback), an intermediate landing is essential. Under the International Residential Code (IRC), any staircase with a vertical rise exceeding 151 inches (12 feet 7 inches) legally requires a landing platform.
This stair calculator with landing computes your flight split, landing platform height, stringer lengths, and horizontal runs while keeping every riser uniform.
How to Use This Stair Calculator with Landing
- Enter your total rise: Measure the vertical distance from finished lower floor to finished upper floor.
- Choose your flight split: The calculator divides risers evenly between flights. Under Adjust, set the number of risers before the landing to match doorways, walls, or room geometry.
- Review both flights: Check the landing platform height, horizontal run for each flight, stringer lengths, and code badges. Print your cut sheet to build lower stringers, the landing, and upper stringers.
How Stairs with Landings Are Calculated
Building a two-flight staircase requires treating both flights as one continuous climb: every riser in both flights must have the exact same height, within 3/8” total variance.
1. Total Risers and Unit Rise
Determine total risers needed for the overall elevation:
Total Risers = Total Rise ÷ 7.75, rounded up
Unit Riser Height = Total Rise ÷ Total Risers
Because unit rise is locked across the system, both flights share identical step heights.
2. Flight Split and Landing Height
Splitting 14 risers at 7 risers creates a balanced midpoint:
Landing Height = Lower Risers × Unit Riser Height
The landing platform serves as the top tread of the lower flight and the starting floor of the upper flight.
3. Flight Runs and Dimensions
For each flight, tread count is risers minus one:
Lower Flight Run = (Lower Risers - 1) × Tread Depth
Upper Flight Run = (Upper Risers - 1) × Tread Depth
This cuts total straight-line horizontal run in half, allowing stairs to fit compact spaces.
4. IRC Landing Code Requirements (R311.7.6)
- Depth: Landings must measure at least 36 inches in the direction of travel.
- Width: Landings must be at least as wide as the stairway (minimum 36 inches).
- Headroom: Maintain at least 6 feet 8 inches (80”) of clearance from landing floor to ceiling.
- Flight Limit: No single flight may exceed 151 inches (12’ 7”) of rise without a landing.
Worked Example: 108” Total Rise (9-Foot Ceiling)
A 9-foot ceiling with 108 inches total rise, split evenly with a landing at 7 risers, using a 10 1/2-inch tread depth:
- Total Rise: 108” (108.0” / 9’ 0”)
- Total Risers: 108 ÷ 7.75 = 13.94 → 14 risers
- Unit Riser Height: 108 ÷ 14 = 7.7143” → 7 11/16”
- Flight Split: 7 risers lower flight, 7 risers upper flight
- Landing Height: 7 × 7.7143” = 54.0000” → 54” (4’ 6”)
- Lower Flight Layout:
- Risers: 7 risers of 7 11/16”
- Treads: 6 treads of 10 1/2”
- Total Run: 6 × 10.5” = 63” → 63” (5’ 3”)
- Diagonal Stringer Length: √(54² + (63 + 10.5)²) = 91.2428” → 91 3/16” (7’ 7 3/16”)
- Lumber Stock: 8-foot 2x12
- Bottom Cut on Lower Stringer (1” tread): 7.7143” - 1.0” = 6.7143” → 6 11/16”
- Upper Flight Layout:
- Risers: 7 risers of 7 11/16”
- Treads: 6 treads of 10 1/2”
- Total Run: 6 × 10.5” = 63” → 63” (5’ 3”)
- Uncut Stringer Throat: 5 1/16” (Passes code, > 5”)
- Framing Square Layout: Tongue at 7 11/16”, Blade at 10 1/2”
- Landing Size: Minimum 36” by 36” (matching stair width).
Both flights comply fully with IRC codes.
Residential Stair Code for Landings (IRC R311.7 / R318.7)
Stairs with intermediate landings must meet these standards:
| Code Dimension | IRC Requirement | Practical Construction Note |
|---|---|---|
| Max Flight Rise | 151 inches (12’ 7”) | Flights exceeding 151” must include a landing |
| Minimum Landing Depth | 36 inches | Measured along the path of travel |
| Minimum Landing Width | Matches stair width | Cannot be narrower than the stairway (min 36”) |
| Max Riser Height | 7 3/4 inches | Must be uniform across both flights |
| Min Tread Depth | 10 inches | Measured nosing-to-nosing |
| Max Riser Variation | 3/8 inch | Greatest vs smallest riser between flights |
| Min Headroom | 6’ 8” (80”) | Clearance above tread nosings and landing floor |
| Handrail Requirement | Required at 4+ risers | Continuous handrail on each flight |
Based on the IRC (2021 R311.7 / 2024 R318.7). Local codes vary — confirm with your building department before building.
Frequently Asked Questions
What is the maximum rise before a stair landing is required?
Under IRC Section R311.7.3, a landing is required on any staircase where the vertical rise between floors or levels exceeds 151 inches (12 feet 7 inches).
What size does a stair landing need to be?
Every landing must measure at least 36 inches in the direction of travel and must be at least as wide as the stairway itself (typically 36 inches or wider).
Can riser heights differ between lower and upper flights?
No. The IRC requires all risers within a staircase—including those before and after a landing—to remain uniform within 3/8 of an inch. Changing riser height between flights causes trip hazards.
What is the difference between an L-shaped and U-shaped stair landing?
An L-shaped stair turns 90 degrees at the landing, requiring a square platform (at least 36”x36”). A U-shaped switchback stair turns 180 degrees, requiring a platform at least double the stair width (typically 36”x72”).
How do I calculate the height of my landing platform?
Multiply the number of risers in your lower flight by your unit riser height. For example, 7 risers of 7 11/16 inches gives a finished landing surface height of exactly 54 inches.
Do I drop the bottom of the upper flight stringer?
Yes. If the upper stringer rests directly on the finished floor or decking of the landing platform, trim the thickness of one tread off the bottom of the upper stringer, just like the lower flight.